Leading 10 usual forklift mishaps ， forklift operation ought to take note of these matters ！.

Don't take too lightly the forklift at the office. If the procedure is bad, there will certainly be serious mishaps in minutes, and there are lots of crashes entailing forklifts.

Instance 1: The forklift freight obstructed the driver's sight, and the person in front could not be found, resulting in a rolling accident.
Case 2: In order to maintain the balance of the forklift when lifting hefty items, the staff members utilized their body weight as the weight, which nearly triggered casualties.
Situation 3: The width of the forklift cargo exceeds the allowable width of the path and hangs on the roadside shelf, which almost causes an crash.
Instance 4: Forklift is speeding up and rolls over during a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift vehicle driver does not use the seat belt, the forklift lifter drops and the vehicle driver is crushed when the forklift rolls over.
Instance 7: The forklift motorist did not wear a safety belt and dropped from the car when it rolled over and was squashed.
Forklift operation need to take notice of these matters ：.

Start.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that prevent the security of driving, beep the horn first and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge must be risk-free before beginning.
3. When the forklift starts with a tons, the driver needs to first validate that the load is steady and reputable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too expensive when driving. When getting in and leaving the job website or while driving, take care that there will be no barriers overhead. When the load is taking a trip, the fork must not be increased expensive, which will certainly affect the stability of the forklift. .
3. After dumping, the fork should be reduced to the regular driving position before driving. .
4. When turning, if there are pedestrians or lorries nearby, the driving signal should be issued first. High-speed doglegs are banned. High-speed sharp turns will trigger the automobile to shed side stability and tip over. .
5. When the forklift is downhill, it is strictly restricted to turn off the flame and slide, and it is prohibited to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and need to maintain a particular safety and security range from the vehicle ahead. .
7. When the forklift is running, the load must be in the lowest position that does not hinder the driving, and the gantry should be properly tilted back. The load will not be elevated other than when piling or filling. .
8. The elevation of the tons should not block the chauffeur's sight. In special circumstances, when the thing influences the forward vision, drive at a reduced rate when reversing.
9. It is forbidden to activate the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is restricted for workers to stand on the fork to hold items and play a stabilizing function. .
12. If problems are found, they will certainly be fixed and reported in a timely manner, and they will never ever operate with diseases Electric Forklift Truck for Warehouse or conceal them.

filling and unloading.
1. When fork-loading items, the range in between the two forks need to be changed as needed to make the lots of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to collaborate with a single fork or make use of a fork top or draw. In special conditions, security indication need to be set up to advise surrounding pedestrians. .
3. In Electric Forklift Truck for Warehouse the process of packing and dumping products, the forklift must be braked with the brake. .
4. The rate of the car need to be sluggish and steady. Be careful not to roll the wheels on the dunnage, so as not to stretch the rolled things and harm individuals. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the tons, and it should be noted that the fork pointer ought to not touch various other goods or items. The lots ought to be maintained with minimal back tilt of the gantry to ensure that the lots does not slide in reverse. The pole can be tilted ahead a little when the load is reduced to permit easy placement of the tons and removal of the forks. .
6. It is forbidden to fork goods at broadband and ram hard objects with the fork head. .
7. When the forklift is working, it is restricted for individuals to loaf the fork, so as to prevent the collapse of the goods and harm people. .
8. Straining is prohibited, and it is restricted to utilize forks to raise employees to take part in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to make use of the brake inertia to slide, place, round or roll things. .
10. It is not allowed to use forks to pick, turn pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to discharge the goods or reduced the fork framework.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for special scenarios, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Eliminate the key. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the look needs to be examined, and gas, lubricating oil and cooling water should be included.
2. Examine the safety and security efficiency of starting, running and braking.
3. Examine whether the lights and horn signals are full and reliable.
4. During the procedure of the forklift, examine whether the stress and temperature level are regular.
5. After the forklift is running, the external leakage must additionally be checked and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You need to inspect prior to leaving the vehicle;.
2. When you come across somebody in front of you during driving, you ought to send a signal at a distance of 5 m;.
3. The driving speed in the factory does not exceed 5 km/h;.
4. When driving, the low point of the freight should be 0.3 m ~ 0.4 m in the air;.
5. The transforming must not be too sharp to stop the propensity of " cost-free turning";.
6. Running up and down the incline must be slow-moving and uniform, and no turning on the slope is permitted.
7. Do not drive throughout the slope. When the gradient is more than 10%, the car needs to be driven backwards when worsening;.
8. When the forklift workers bring the goods and move forward, if they run into big or hefty products and go to the vehicle driver's line of sight, they must take the turning around exercise
.
The "Eight Prohibitions" must be followed in the operation.
1. Single fork operation is not permitted.
2. It is not allowed to lift the goods for cross country driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to pick up the goods.
6. It is not enabled to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not enabled to bring individuals to work with the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Auto parking is not permitted under the following conditions.
1. Curves, slim roads, train crossings;.
2. Areas with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of the road, the contrary side of the area with the very same size as the challenge should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844